SSI Anchors and Hammer Drill Bits

Quality for Professionals


Secure Systems International (SSI) Pte Ltd

Tel: (65) 6515 5328 / 9173 4630






Structural Epoxy-Tie Anchoring Adhesive for Cracked and Uncracked Concrete

CA_Set XP EMN22i EDT22S SET-XP Tested

SET-XP® is a 1:1 two component, high solids epoxy-based anchoring adhesive formulated for optimum performance in both cracked and uncracked concrete. SET-XP® adhesive has been rigorously tested in accordance with ICC-ES AC308, 2009 IBC and ETAG requirements and has proven to offer increased reliability in the most adverse conditions, including performance in cracked concrete under static and seismic loading. SET-XP® adhesive is teal in color in order to be identifi ed as a high-performance adhesive for adverse conditions. Resin and hardener are dispensed and mixed simultaneously through the mixing nozzle. SET-XP® adhesive exceeds the ASTM C881 specifi cation for Type I and Type IV, Grade 3, Class C epoxy.


When SET-XP® adhesive is used with all threaded rod or rebar, the system can be used in tension and seismic zones where there is a risk of cracks occurring that pass through the anchor location. It is also suitable for uncracked concrete conditions.


ICC-ES ESR-2508; City of L.A. pending; Florida FL 11506.5 NSF/ANSI Standard 61 (313 cm2/1000 L). The load tables list values based upon results from the most recent testing and may not refl ect those in current code reports. Where code jurisdictions apply, consult the current reports for applicable load values. ETA-11/0360.

Test Criteria:

Anchors installed with SET-XP® adhesive have been tested in accordance with ICC-ES's Acceptance Criteria for Post-Installed Adhesive Anchors in Masonry Elements (AC58) and Adhesive Anchors in Concrete Elements (AC308) for the following:

  • Seismic and wind loading in cracked and uncracked concrete and uncracked masonry 
  • Static tension and shear loading 
  • Horizontal and overhead installations 
  • Long-term creep at elevated temperatures 
  • Static loading at elevated temperatures 
  • Damp holes 
  • Freeze-thaw conditions 
  • Critical and minimum edge distance and spacing 

SET-XP® Material Property:

 SET-XP Material Property

Chemical Resistance:

Very good to excellent against distilled water, in-organic acids and alkalis. Fair to good against organic acids and alkalis, and many organic solvents. Poor against ketones.

Cure Schedule:

Cure Schedule

SET-XP® Cartridge System:

SET-XP Cartridge System

Shelf Life:

24 months from date of manufacture in unopened side-byside cartridge.

Storage Conditions:

For best results, store between 7–32° C. To store partially used cartridges, leave hardened nozzle in place. To re-use, attach new nozzle.


Resin – white, hardener – black-green. When properly mixed, SET-XP adhesive will be a uniform teal color.

Clean Up:

Uncured material – Wipe up with cotton cloth. If desired, scrub area with abrasive, waterbased cleaner and fl ush with water. If approved, solvents such as ketones (MEK, acetone, etc.), lacquer thinner or adhesive remover can be used. DO NOT USE SOLVENTS TO CLEAN ADHESIVE FROM SKIN. Take appropriate precautions when handling flammable solvents. Solvents may damage surfaces to which they are applied. Cured Material – chip or grind off surface.


SET-XP® Epoxy Anchor Installation Data (ETA-11/0360)

SET-XP® Epoxy Anchor Installation Data (ETA-11/0360)

SET-XP® Epoxy Characteristic values of resistance to tension loads. Design method TR 029

SET-XP® Epoxy Characteristic values of resistance to tension loads

SET-XP® Epoxy Characteristic values of resistance to shear loads. Design method TR 029

SET-XP® Epoxy Characteristic values of resistance to shear loads


Adhesive Anchoring Installation Instructions

Hole Preparation 

Cartridge Preparation

Filling the Hole

Filling the hole

Filling the Hole

Note Note: Always check expiration date on product label. Do not use expired product.

Note Warning: When drilling and cleaning hole use eye and lung protection. When installing adhesive use eye and skin protection.

Product Listing

Product List - Set-XP

Back to Chemical Anchors